Obiekt
Tytuł: Durability tests of ball valve prototype with flowmeter operation
Współtwórca:
Tytuł publikacji grupowej:
Abstract:
The results of the investigation of the prototypical ball valve are presented in this article. The innovation of the tested valve is a ball with a built-in measuring orifice. The valve has been subjected to durability tests. Leakage under three temperatures: ambient, -30 degress C and +100 degress C was analyzed. Sealing elements of the valve were tested for roughness and deviation of shape before and after the cycles of operation. ; Ball valve operation means cycles of open/close. It was planned to perform 1000 cycles at each temperature condition accordingly. Tests of the valve were performed under gas pressure equal to 10 MPa. The research was carried out under the Operational Program "Intelligent Development" (POIR 01.01.01-00-0013 / 15 "Development of devices for measurement of media flow on industrial trunk-lines".
Wydawca:
Zielona Góra: Uniwersytet Zielonogórski
Format:
Identyfikator zasobu:
DOI:
Strony:
Źródło:
IJAME, volume 23, number 1 (2018)
Jezyk:
Licencja:
Licencja CC BY-NC-ND 4.0:
Prawa do dysponowania publikacją:
Biblioteka Uniwersytetu Zielonogórskiego
Kolekcje, do których przypisany jest obiekt:
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Jednostki organizacyjne > Wydział Mechaniczny
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Typy utworów > Artykuły
- Zielonogórska Biblioteka Cyfrowa > Repozytorium > Czasopisma naukowe i serie wydawnicze UZ > International Journal of Applied Mechanics and Engineering (IJAME) > International Journal of Applied Mechanics and Engineering (IJAME) (2018)
Data ostatniej modyfikacji:
2023-07-06
Data dodania obiektu:
2023-03-31
Liczba wyświetleń treści obiektu:
35
Wszystkie dostępne wersje tego obiektu:
https://www.zbc.uz.zgora.pl/publication/80066
Wyświetl opis w formacie RDF:
Wyświetl opis w formacie OAI-PMH:
-
International Journal of Applied Mechanics and Engineering (IJAME)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 28 (2023)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 27 (2022)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 26 (2021)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 25 (2020)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 24 (2019)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23, number 1 (2018)
- International Journal of Applied Mechanics and Engineering (IJAME), volume 23, number 1 (2018) - spis treści
- Two-dimensional deformation in a thermoelastic solid with microtemperatures subjected to an internal heat source
- Modelling of the flow of streams of cohesionless and cohesive bulk materials in a conveyor discharge point with a flat conveyor belt
- Experimental and numerical analysis of fracture in 41Cr4 steel - issues of the stationary cracks
- Stability assessment as a criterion of stabilization of the movement trajectory of mobile crane working elements
- Shapes of an air taylor bubble in stagnant liquids influenced by different surface tensions
- Compressible analysis of Bénard Convection of magneto rotatory couple-stress fluid
- Modelling of the human knee joint supported by active orthosis
- Effect of seepage on change in stress distribution scenario in static and seismic behaviour of earthen dams
- Effects of heat source/sink and chemical reaction on MHD maxwell nanofluid flow over a convectively heated exponentially stretching sheet using homotopy analysis method
- Simulation of the flow through porous layers composed of converging-diverging capillary fissures or tubes
- Flows of newtonian and power-law fluids in symmetrically corrugated cappilary fissures and tubes
- The effect of multigrid parameters in a 3D heat diffusion equation
- Identification of the cause of the stem neck fracture in the hip joint endoprosthesis
- Durability tests of ball valve prototype with flowmeter operation
- Selected aspects of cryogenic tank fatigue calculations for offshore application
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23, number 2 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23, number 3 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23, number 4 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 23, number 1 (2018)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 22 (2017)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 21 (2016)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 20 (2015)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 19 (2014)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 18 (2013)
-
International Journal of Applied Mechanics and Engineering (IJAME), volume 29 (2024)
| Nazwa wydania | Data |
|---|---|
| Durability tests of ball valve prototype with flowmeter operation | 2023-07-06 |
